Atv61 Display Status Change

Setting GUI Status on CL_SALV_TABLE. Display of the parameters selected by the user The four W parameters give the value of the four monitored words selected by the user.

Configuring Altivar 61 71 Keypad To Display Multiple Parameters Schneider Electric Support Youtube

Turn the navigation dial clockwise to increase the digit or counter-clockwise to decrease the digit.

Atv61 display status change. Go to Drive Menu 18 Fault Management Undervoltage Mgt. Use F1 and F2 to scroll horizontally then select the. B1 Identifying the existing ATV 38 vMake an inventory of your Altivar 38 installation.

650 588-9200-Outside Local Area. How can I prevent Undervoltage faults on ATV61 drives. Refer to the Altivar 61 ATV61 programming manual for detailed information about the display terminal operations.

The document provides information about migrating from ATV61 to ATV630 or ATV650 and from ATV71 to ATV930 or ATV950. Importantly it includes product selection according to the existing. CLI Current Limitation is a status code not a fault code.

B3 Mounting vMount the drive in accordance with the instructions in this document using the. It can eventually trigger a fault which will cause the drive to lockout. COMMUNICATION The integrated 7-segment display terminal menus are shown in round brackets.

Box 27446 Raleigh NC 27611-7446 For support and assistance contact the Product Support Group. Setpoint 1 configuration Network card Setpoint 1 comes from Ethernet. 30072-451-60C Altivar61 Variable Speed Drive Controllers Simplified Manual 092008 Table of Contents 9.

Emis_Para array of 16 INT for data to send. ATV6171 EtherCAT Overview HRB14105 042013 13 Notation rules in this manual Drive Terminal Displays The graphic display terminal to be ordered separately - reference VW3A1101 menus are shown in square brackets. It indicates that the unit is operating at current limit based on the programmed threshold in the Settings or.

Use F1 and F2 to scroll horizontally then select the digit to change the digit is highlighted. Courtesy of Steven Engineering Inc-230 Ryan Way South San Francisco CA 94080-6370-Main Office. If the drive is running and the voltage applied to the PWR input terminal drops below 19Vdc the drive will stop and display NST.

Code is displayed on HMI Resolution. Check all the output connections from the drive to the motor. Once configured a tick will appear next to PID requl verifying selection.

Configuration via the graphic display terminal or the integrated display terminal. Set the switch to Source factory setting if using PLC outputs with PNP transistors. ATV6171 drive is displaying a OPF2 fault code.

Steps 3 and 4 must be performed with the power off. Read and understand these instructions before perf orming any procedure on this drive controller. My problem is that I cant link a GUI status to this as the status can only be linked to a program function module etc.

Change this with your ATV61 AV71 IP address keeping the same syntax -TYP1. Schneider Electric AC Drives Product Support Group PO. The products described in this document may be changed or modified at any time either from a technical point of view or in the way they are operated.

Change the Undervoltage timeout from 02s to somewhere between 5-10s. Set the switch to Sink Int or Sink Ext if. The address and display format of these parameters can be configured in the 6 - MONITORING CONFIG menu 63.

Changing a parameter 1. Press ENT to save the change or press the ESC button to cancel the change. CLI status on an ATV61 and ATV71 drive.

For the ATV6171 VFD only. Parameter Value Comment Profile Drivecom profile separate The run commands are in Drivecom profile the command and the setpoint can come from different channels. You will need to make sure you close the 24 VDC to PWR input and cycle off and on the run command again.

VChoose the various options required. I have added a new GUI status to a FM in the same package but Im. The drive has protection to prevention damage to the drive if wired incorrectly but will display NLPAnother possibility.

On the display terminal the 12 - MONITORING SUP- menu COMMUNICATION MAP CMM- submenu CANopen MAP submenu can be used to display the communication status on CANopen. 2 In the 11 SIMPLY START menu enter the Macro configuration screen and select PID regul to select this Enter must be held down for 2 seconds. Select the parameter to change and press ENT.

How do I change the contrast and stand-by time on the ATV61 and ATV71 keypads. This is where the Modbus message to be sent is assembled. Their description can in no way be considered contractual.

Set popup display lo_alv-set_screen_popup start_column 10 end_column 200 start_line 5 end_line 30. This is the only possible value do not change -EMIS. J ALTIVAR 61 GRAPHIC DISPLAY TERMINAL E C B A F G H I K D RDY Term 000 Hz REM.

The screenshot in Step 6 Comment area explains what each register is. Or if a safety circuit is. Motor is not connected output contactor if used is not closing fast enough or the motor current draw is too low.

13 SETTINGS SEt- menu High torque thd ttH Low torque thd ttL Pulse warning thd FqL Freewheel stop Thd FFt 14 MOTOR CONTROL drC- menu Extension of the following configurations to all drive ratings previously limited to 45 kW 60 HP for ATV61 pppM3X and to. Check all the motor parameters and make sure the set values match the motor. Altivar 61 Altivar 71 Environment.

Continue down the 11 SIMPLY START menu and set motor nameplate acceleration. ATV6171 PROFINET Manual VW3A3327 HRB25667 Eurotherm by Schneider Electric. In supporting the transition Schneider Electric produces a 65-page Migration Manual for Altivar Process Drives when replacing ATV61ATV71 with ATV630ATV930.

LED display RUN LED LED OFF Stopped Pre-operational or Operational state of the CANopen controller ERR LED LED CANopen error. The drive is showing nLP no line power but a meter check between the PA and PC- terminals show good DC bus voltage. If the line voltage is less than 480VAC we can also look at adjusting the Mains Voltage setting to 460V which lowers the trip level for the Undervoltage fault.

Make sure the factory-installed jumper between 24 and PWR is connected firmly. The logic input switch SW1 is used to adapt the operation of the logic inputs to the technology of the programmable controlle r outputs. ATV61 ATV71 Environment.

Status word display The Status word parameter gives the value of the status word ETA. For more information call fax or write. B2 Selecting the ATV 61 vDetermine the Altivar 61 catalog number.

Use the navigation dial to vertically scroll the DRIVE MENU list press ENT navigation button to select the submenu. It is based on the Modbus Application Protocol Specification document.

Troubleshooting Pra Status On Altivar 61 71 Drives Schneider Electric Support Youtube

Altivar Process How To Import Graphic Display Terminal Configuration Files In Somove Youtube

Altivar 61 Drives By Schneider Electric Frequently Asked Questions

Configuring Atv61 Atv71 For 0 10vdc Speed Reference On Ai2 Schneider Electric Support Youtube

Configuring Displayed Values On Altivar Process Drives Schneider Electric Support Youtube

Programming Freewheel Stop On Altivar 61 71 Drives Schneider Electric Support Youtube